(503) 491-4848

CCB: #112220
STEP Warmfloors

Perfect Climate, Inc. and STEP warmfloor™… a step ahead!

Perfect Climate, Inc. is a Master Distributor and installer for STEP Warmfloor™ products… the ultimate in radiant floor heat. This innovative, energy-efficient, patented electro plastics element is distinctly different from hydronic (water tubing) and cable systems.

STEP Warmfloor™ gives a comfortable, even heat and is the only low-voltage, self-regulating system available. The product was developed in 1981 and has been used for over 25 years worldwide.

Key Benefits:

  • Comfort – continuous even heat distribution which minimizes drafts allowing for a lower room temperature
  • Safety – low-voltage AC or DC system (24 volts) with no risk to your family
  • Energy Efficient – self-regulating, therefore drawing only the required energy to maintain an ideal temperature
  • Health – does not circulate dust and allergens that can cause respiratory problems
  • Ease of Installation – can be installed under most floor coverings, including tile, stone, resilient, laminate, wood, and carpet. See the DIY Kitchen Renovation Installation Video at the bottom of this page
  • Environmentally Friendly – made of non-hazardous material that is recyclable
  • Maintenance-Free – virtually no maintenance needed for the life of your flooring
  • Made in the USA – manufactured in-house, thus producing US jobs

STEP Warmfloor™ is a heating system designed to meet demands for human comfort, safety and energy efficiency. It is the most advanced in quality, usage, and durability. STEP Warmfloor™ is SELF-REGULATING

STEP Warmfloor™ is a flexible, homogeneous, polymer heating element. The plastic is electrically conductive; because of resistance in the material, heat develops. The element is self-regulating which means that when the ambient temperature rises, the electrical resistance increases and the consumption of electricity decreases. For this reason, the element cannot overheat.

STEP Warmfloor™ is LOW-VOLTAGE

STEP Warmfloor™ operates on low-voltage and does not require a ground fault switch. It is normally connected to a 24 volt transformer, but can also be run by solar or wind-power sources. The system is maintenance free, easily zoned and energy efficient.

STEP Warmfloor™ is DURABLE

STEP Warmfloor™ is a strong, thin, plastic mat, 3/64 inch (1.2 mm) thick. It comes in a roll, in different widths, and can be cut to the desired length and field-wired on site. The formula to calculate the maximum element length per fuse (5A) in the terminal board is 24V x 5A / XX W/ft; the formula for the maximum total element length (8A) with two jumped fuses is 24V x 8A / XX W/ft.

STEP Warmfloor™ is EASY TO INSTALL

STEP Warmfloor™ can be installed in new construction and is ideal for renovation projects because of the thinness of the material. The heating elements come in a roll and are cut to size on site. The system is suitable and easy to fit in a whole house or only in areas where extra heating is required.

The heating elements can be installed on any stable, clean and dry surface. Secure the elements to the substrate so that they do not overlap or touch each other. This can be done using latex modified mortar, staples, hot melt glue, and only recommended tape and adhesives as they can negatively affect the heating properties of the semi-conductive elements. Do not penetrate with staples or nails the two bus braids on each side of the elements; this could create a short circuit and be a fire hazard. Make the electrical connections and run the wires to the transformer following manufacturer’s instructions, electrical and local codes. The wires can be routed on the floor, up the wall, under the baseboard, or in raised foundations, under the subfloor. Cover the elements and finish the floor according to trade practices.

STEP Warmfloor™ is TOTAL HEAT

STEP Warmfloor™ can be used as the primary heat source of a building. Heat requirements depend on room size and usage, insulation values, location and outside average temperature. A heat loss calculation is necessary. It is very convenient to have a heating system that can go under all types of floor coverings.

STEP Warmfloor™ is COMPLEMENTARY HEAT

STEP Warmfloor™ can be installed when additions are made to a house and the existing heating system is insufficient. Make a basement comfortable without overheating the whole house or add heat to a sunroom.

STEP Warmfloor™ is FLOOR WARMING

STEP Warmfloor™ eliminates cold floors. It is essential in a bathroom under ceramic tiles and it can be used in any room, under most finished floorings, including wood, laminate, carpet, resilient, and natural stone. The elements can also be installed between the floor joists when the existing floor covering is to be maintained.

STEP Warmfloor™ is ENERGY EFFICIENT

STEP Warmfloor™ can be placed safely closer to the floor surface than any other heating system. With less mass to heat, the system reacts fast to its regulated temperature.

The even distribution of heat eliminates drafts and gives a pleasant comfort at a lower temperature. Maintaining a continuous even temperature is more efficient than an on-and-off heating system.

The self-regulating heating elements only draw the energy required to maintain the ideal temperature. Individual zoning for each room is not only comfortable but also very cost effective.

When thinking of efficiency, you should take in consideration:

  • Consumption – how much energy does the system pull compared to other heating options.
  • Cost – what is the cost per kWh in the area (winter rates) compared to other available energy sources. Maintenance comparison should be added to the cost.

Note: For a heating system to be efficient it is very important to have sufficient thermal insulation. Heat goes to cold in all directions (360 degrees). If the area is not properly insulated, you may not attain the desired floor and ambient temperature and the system will not be energy efficient.

Areas We Serve

Battle Ground

Clackamas

Happy Valley

Sandy

Beavercreek

Colton

Heisson

Stevenson

Beaverton

Corbett

Lake Oswego

Troutdale

Boring

Damascus

Marylhurst

Tualatin

Bridal Veil

Eagle Creek

Mulino

Vancouver

Brightwood

Estacada

North Bonneville

Washougal

Brush Prairie

Fairview

Oregon City

Welches

Camas

Gladstone

Portland

West Linn

Cascade Locks

Gresham

Ridgefield

Yacolt

24/7 emergency service available - Call us Today at (503) 491-4848

© 2018 Perfect Climate, A Wolcott Company